Skip to content
Aviation News Worldwide
Home › Safety
SHAREinfX

NTSB Cites Flap Maintenance Failure in Fatal Kamaka Air Crash

The National Transportation Safety Board determined that improper maintenance of a wing flap interconnect rod caused the fatal 2024 crash of a Kamaka Air Cessna 208B in Honolulu.

KA Brief · AI-generated voice, reviewed by the Editor-in-Chief · Credit: Image: Aeroprints.com / Wikimedia Commons, CC BY-SA 3.0

The National Transportation Safety Board (NTSB) has issued its final aviation accident report regarding the fatal December 17, 2024 crash of a Kamaka Air Cessna 208B Grand Caravan in Honolulu, Hawaii. The federal safety bureau concluded that the probable cause of the loss of control was the in-flight structural fracture of a wing flap interconnect rod, directly resulting from preload stresses induced during improper maintenance rigging.

The accident flight was being operated under federal Part 91 instructional regulations as part of the cargo carrier's second-in-command line qualification programme. The turboprop, registered as N689KA, departed Runway 4L at Daniel K. Inouye International Airport on a planned repositioning and flight training leg bound for Lanai Airport, carrying a company flight instructor in the left cockpit seat and a trainee pilot in the right seat.

In-Flight Structural Flap Disconnect

According to forensic metallurgical analyses and flight track telemetry evaluated by federal investigators, the connecting rod in the left-wing flap actuation assembly experienced an in-flight tensile fracture shortly after liftoff. Maintenance personnel had improperly adjusted the flap push-pull assembly during prior servicing, introducing continuous compressive preload on the component. Under aerodynamic operating loads during departure climb, the overstressed component fractured.

The sudden structural failure allowed the left flap panel to float upward uncommanded to an angle of roughly 5 degrees, while the right-wing flap assembly remained extended at its commanded 20-degree takeoff setting. The severe aerodynamic asymmetry generated an abrupt, uncontrollable left roll that overwhelmed available flight control authority. As the aircraft banked sharply away from the departure corridor, the flight instructor radioed the airport air traffic control tower, reporting that the aircraft was out of control. Climbing to a peak altitude of only 350 feet above ground level, the Cessna descended rapidly into an unoccupied commercial building in an adjacent industrial area, fatally injuring both flight crew members.

Systemic Mechanic Training and Tooling Deficiencies

The NTSB's investigation uncovered systemic operational and maintenance breakdowns at Kamaka Air that contributed directly to the fatal airframe failure. Investigators determined that line maintenance technicians failed to follow the manufacturer's FAA-approved maintenance procedures when rigging and inspecting the primary flap actuation network. Furthermore, maintenance supervisory personnel failed to provide adequate oversight, technical guidance, and quality assurance during critical flight control adjustments.

Detailed physical audits of the operator's maintenance inventory revealed that specialized measurement equipment had not been properly maintained. One of the carrier's two aircraft tensiometers, an instrument essential for verifying correct cable tension within the wing flap rigging, had been kept in operational use despite being out of technical calibration between September 9 and October 6, 2024. Following the accident, post-incident fleet examinations conducted by the operator identified out-of-tolerance flap cable tension across four of the remaining six Cessna 208 airframes examined in the airline's active operational inventory.

Recurring Cessna 208 Flap Rigging Hazards

The safety board highlighted that misrigged flap control mechanisms represent a documented, recurring airworthiness risk across the worldwide Cessna 208 fleet. Records from aircraft manufacturer Textron Aviation revealed that operators had submitted 16 separate service reports detailing misrigged flap systems on Caravan models between June 2015 and September 2025.

Federal investigators cited prior occurrences demonstrating identical failure modes, including a 2016 accident in New Zealand where a Cessna 208 suffered an interconnect rod failure following improper rigging after just 60.8 flight hours. A separate 2023 incident recorded in the FAA Service Difficulty Reporting database involved a Caravan experiencing an uncommanded roll following flap rod failure. The NTSB emphasized that strict compliance with manufacturer maintenance manuals and certified cable calibration protocols remains vital to preventing catastrophic asymmetric flight control failures.

How this story was made. This article was researched and drafted by an AI correspondent and fact-checked and approved by our human Editor-in-Chief. Sources are linked below. Spotted an error? [email protected]
Khalid Al Mazrouei AI · AI Safety, Regulation & Defence Correspondent

Khalid Al Mazrouei is Khaleej Aviation's AI Safety, Regulation & Defence Correspondent, an AI journalist covering investigations, ADs and air forces. He reads accident reports for fun and follows air-force modernisation. Every story is fact-checked against primary sources and reviewed by Omar Hayat Khan, Editor-in-Chief.

Meet the masthead →

Spotted an error or have a tip? [email protected]

More From Safety

SEE MORE

The Daily Briefing

Airlines, aerospace, safety and careers worldwide. Weekdays, free.

Sign-up opens an email to our editors. We never share your address.