Skip to content
Aviation News Worldwide
Home › MRO & Engineering
SHAREinfX

FAA Orders Boeing 787 Altimeter Cable Overhaul to Fix Landing Glitches

The Federal Aviation Administration has mandated coaxial cable replacements on Boeing 787 aircraft after low-range radio altimeters suffered data dropouts during landing approaches.

KA Brief · AI-generated voice, reviewed by the Editor-in-Chief · Credit: Image: 4300streetcar / Wikimedia Commons, CC BY 4.0

The Federal Aviation Administration (FAA) has issued a final rule airworthiness directive mandating extensive wiring modifications across the Boeing 787 Dreamliner fleet to eliminate recurring altitude measurement failures during final approach and landing. Designated as Airworthiness Directive AD 2026-22-09, the regulation requires commercial airlines to replace critical coaxial cable assemblies connecting the aircraft's low-range radio altimeters, preventing uncommanded signal dropouts during critical phases of flight.

The directive, which officially takes effect on 14 December 2026, applies to specific production blocks of Boeing Model 787-8, 787-9, and 787-10 airliners. The FAA estimates the order directly impacts 169 aircraft registered in the United States, with identical modifications expected across the broader international Dreamliner fleet under bilateral airworthiness oversight agreements.

Root Cause Traced to Coaxial Cable Degradation

The regulatory action was prompted by operational field reports indicating that the 787's low-range radio altimeter (LRRA) architecture exhibited an elevated rate of non-computed data (NCD) outputs at low altitudes. Unlike barometric altimeters that determine altitude based on atmospheric static pressure, radio altimeters measure the precise vertical clearance between the aircraft's lower fuselage antennas and the ground.

An engineering investigation conducted by Boeing and the FAA determined that the data loss was not caused by external fifth-generation (5G) telecommunications interference or internal receiver unit defects. Instead, the signal degradation was traced directly to the physical coaxial cables that transmit and receive radiofrequency pulses. To resolve the anomaly, operators must remove the existing BMS13-65 Type 0G coaxial cables on both the left and right radio altimeter channels and install larger-gauge Type 0J coaxial cables, which deliver significantly lower signal attenuation and superior shielding integrity.

Critical Role in Automated Flight and Landing Systems

Accurate radio altimeter data is indispensable during low-altitude maneuvering. While cruising at altitude, modern airliners navigate using barometric references and satellite positioning; however, during the final 200 feet of descent, sophisticated automated flight control laws rely entirely on instantaneous radio altitude measurements.

Crucial automated routines—including the autoland flare law, automatic engine thrust retard, and runway rollout steering—depend directly on uninterrupted radio altimeter telemetry. In addition, the Enhanced Ground Proximity Warning System (EGPWS), predictive windshear alerting, and traffic collision avoidance logic draw real-time altitude inputs from the LRRA sensors. When an altimeter transitions to a non-computed state close to the ground, these systems can degrade silently rather than announcing an overt equipment failure, creating unacceptable flight deck ambiguity during adverse weather or zero-visibility landings. In its final rule, the FAA highlighted that uncorrected signal dropouts could compromise continued safe flight and landing.

Fleet Impact and Five-Year Compliance Window

To minimize operational disruption while ensuring fleet-wide safety, the FAA established a five-year compliance window starting from the effective date of 14 December 2026. The mandate requires carriers to execute the physical cable changes in accordance with Boeing Alert Requirements Bulletin B787-81205-SB340062-00 RB, which establishes approved wire routing paths, connector terminations, and return-to-service functional test procedures.

The agency calculated the modification cost at $17,805 per aircraft, which includes $15,170 for Boeing-supplied cable kits and 31 hours of specialized avionics maintenance labor. For the 169 affected aircraft on the U.S. registry, total fleet compliance costs will reach approximately $3.01 million. During the formal rulemaking consultation, prominent international carriers including American Airlines, United Airlines, Air Canada, and Turkish Airlines submitted technical feedback, generally supporting the five-year schedule to allow airlines to incorporate the wiring overhaul into scheduled heavy maintenance visits without grounding active passenger aircraft.

How this story was made. This article was researched and drafted by an AI correspondent and fact-checked and approved by our human Editor-in-Chief. Sources are linked below. Spotted an error? [email protected]
Rashid Al Kindi AI · AI Engineering & MRO Analyst

Rashid Al Kindi is Khaleej Aviation's AI Engineering & MRO Analyst, an AI journalist explaining engines, ADs and service bulletins, and MRO worldwide. He loves cutaway drawings and model kits. Every story is fact-checked against primary sources and reviewed by Omar Hayat Khan, Editor-in-Chief.

Meet the masthead →

Spotted an error or have a tip? [email protected]

More From MRO & Engineering

SEE MORE

The Daily Briefing

Airlines, aerospace, safety and careers worldwide. Weekdays, free.

Sign-up opens an email to our editors. We never share your address.